Mingjiada Electronics stock supply of the MPS MP8772—a 12A, 17V, 700kHz synchronous buck converter in a 3mm × 3mm QFN-16 package. Its COT control delivers extremely fast transient response. Genuine factory products are stocked in both Shenzhen and Hong Kong warehouses, ensuring rapid delivery for both samples and bulk orders.
I. Core Positioning of the MP8772: Packing “High Current” into a Small Package with COT Control
The MP8772 is a fully integrated, high-frequency synchronous rectification buck switch-mode converter that integrates low-on-resistance power MOSFETs (16 mΩ for the upper switch and 5.5 mΩ for the lower switch) and delivers a continuous output current of up to 12 A. Its competitive edge lies not in the extremes of any single parameter, but in the balance of multiple characteristics within a compact footprint:
COT control delivers system-level simplification. The Constant On-Time (COT) architecture eliminates the need for loop compensation networks required by traditional voltage-mode or current-mode designs. It features extremely short duty cycle adjustment delays during load steps, resulting in transient response speeds significantly superior to fixed-frequency PWM solutions, while also greatly simplifying loop design and reducing the number of external compensation components. For applications sensitive to dynamic load changes—such as CPU/SoC power supplies and FPGA core power supplies—this feature directly translates to a cleaner output voltage and lower bulk capacitance requirements.
The wide input range and adjustable output voltage cover mainstream rail voltages. The 3V to 17V input range supports 12V intermediate buses, 5V system rails, and certain battery-powered scenarios; The output voltage is adjustable from 0.6V up to 12V, covering common digital and analog rails such as 0.9V, 1.0V, 1.2V, 1.8V, 3.3V, and 5V.
Comprehensive protection and timing functions. The chip integrates short-circuit protection (SCP), overcurrent protection (OCP), undervoltage protection (UVP), and hiccup-mode thermal shutdown; The PG pin can be used for power-up sequencing control in multi-output power supply applications, and an externally programmable soft-start feature allows the power-up slope to be set according to load characteristics, thereby suppressing inrush current.
II. Key Specifications at a Glance
Function Type: Synchronous buck DC-DC converter
Input Voltage Range: 3V – 17V
Output Voltage: 0.6V – 12V, adjustable
Continuous Output Current: 12A
Switching Frequency: Fixed at 700 kHz
On-chip MOSFET RDS(ON): 16 mΩ (upper MOSFET) / 5.5 mΩ (lower MOSFET)
Control Architecture: Constant On-Time (COT)
Quiescent Current: 100 µA
Package: QFN-16 (3 mm × 3 mm)
Operating Junction Temperature: –40°C to +125°C
III. Typical Application Scenarios: From Security Cameras to Industrial Load Points
The MP8772’s application profile is quite clear: it is suited for space-constrained environments with current requirements ranging from several amperes to over ten amperes, where the input voltage is primarily 12V or 5V, and where transient response is critical.
Security cameras and vision modules. The core and I/O power supplies for the main SoC or image sensor require a small package and fast load tracking; COT control is well-suited for the step response of image processing loads, and the 3mm × 3mm package fits within the limited board area of camera modules.
Portable devices and xDSL/set-top boxes. A 100 µA quiescent current, combined with the efficiency advantages of synchronous rectification under light loads, is particularly relevant for battery-powered devices or those with standby power consumption requirements; digital set-top boxes, flat-panel TVs, and monitors are also scenarios frequently highlighted in MPS’s official and application documentation.
Industrial and telecommunications load points. The 12V bus is directly stepped down to core voltages such as 0.9V, 1.0V, or 1.2V, and the 12A output capability meets the load requirements of multi-core processors, FPGAs, and ASICs; the PG and external soft-start features facilitate multi-rail sequencing management.
For designs that previously used a discrete “controller + external MOSFET” solution, the MP8772 offers the most direct benefits in terms of reduced board area and component count.
IV. Why Source the MP8772 from Mingjiada
The chip’s specifications determine “whether it can be used,” while the supply channel determines “whether it can be used reliably.” Mingjiada Electronics’ supply capabilities for MPS power devices focus on three key areas:
Genuine OEM products and channel reliability. Founded in 1996, Mingjiada is an authorized independent distributor of electronic components. It has obtained ISO 9001 and ISO 14001 certifications and maintains long-term supply relationships with over 500 semiconductor manufacturers, including MPS. The MP8772GQ is sourced through genuine OEM channels; the suffixes “-P” and “-Z” indicate only differences in packaging format, while the chip itself remains identical, allowing for flexible selection based on production line packaging requirements.
Deep Stock Availability and Fast Delivery. Mingjiada operates a dual-warehouse inventory system in Shenzhen and Hong Kong, with stock covering over 2 million part numbers. For common packaging types of the MP8772GQ, we can fulfill both sample requests and volume orders; standard orders are shipped within 1–3 days, and lead times can be further reduced for urgent requests. This inventory structure offers greater flexibility than relying solely on the original manufacturer’s lead times, particularly for sample requirements during the R&D phase and replenishment schedules during mass production ramp-up.
Continuous Coverage of the MPS Product Line. Mingjiada has long specialized in the spot supply of MPS power management chips, covering multiple product lines ranging from DC-DC converters to power modules and motor drivers. The MP8772 can be ordered alongside devices from the same series within a single supply window, reducing the coordination costs associated with multiple suppliers.
For MP8772 samples, volume quotes, or combined ordering solutions with other MPS devices in the same series, please contact the Mingjiada Electronics sales team directly to obtain real-time inventory and lead time confirmation.
Contact Information: Mingjiada Electronics official website www.integrated-ic.com; Sales Team +86 13410018555; Email sales@hkmjd.com.
コンタクトパーソン: Mr. Sales Manager
電話番号: 86-13410018555
ファックス: 86-0755-83957753
Japanese
